Metals

Metals are hard, strong and tough and by their nature, are malleable, fusible and ductile which means that they can be formed into a vast array of desired shapes without cracking or breaking. Due to their nature they can be treated to alter characteristics and formed to meet the requirements of any number of applications.

Metal Testing Goal:

Testing the mechanical properties of metallic materials determines if it meets the requirements of a desired application. The most common characteristics measured during testing are the modulus of elasticity, yield strength, tensile and compressive strength, and elastic limit. Metals are also tested to measure modulus of rigidity, shear strength, bend strength, flexure strength and fatigue strength as well as the time dependent behavior such as creep and stress relaxation. These values provide an accurate depiction of the behavior that a metal material may be expected to exhibit during loading and the lifetime of its application.

Common Metal Test Methods:

Test methods for metals tend to be very similar as those used for the testing of other materials such as plastics or composites. Flexure, bend, shear and torsion tests are all performed on metals, but the most common tests are the tension, compression and fatigue tests.Tension and compression testing involve the metal sample experiencing a load along one of its axis that either pulls the material apart or pushes it together. These tests are generally run until the sample fails or ruptures but may be stopped at any time.

Shear and torsion tests require that the sample experiences opposing loads at each end that act perpendicularly to the axis of the sample. A shear tests will pull the ends of the sample so it will fail in a sliding motion whereas a torsion test will twist the ends of the sample so it will fail in a turning motion.

A metal sample for flexure and bend tests will experience a load at its midsection while it is supported at its two ends. As the load is increased the sample will be deformed into a “U” or “V” shape depending upon its characteristics.

Fatigue testing measures time and cycle dependent behavior of metals through cyclic loading. These tests measure the number of cycles till failure, the time till failure, and possibly creep and stress relaxation rates of the metal samples.

All of these tests are used to determine if a metal material is suitable for an application and are often combined with each other to create an accurate representation of the stresses a metal material will experience in its lifetime.

Metal Testing Specimens:

Testing specimens made from metal can essentially take any form. They commonly come in the shape of dog bones, dumbbells, rods, bars, cylinders, cubes, bricks, and tubes. The difference between test samples made from metal and test samples made from other materials is in the microstructure. Metals can undergo processes such as heating, quenching, annealing and others that alter its microscopic composition. Specifically the grain size, grain orientation and the dislocations are altered to change the characteristics of the metal such as its strength, toughness, and ductility.

Related Articles

• Tensile Strength Test of Fibers, Threads, Wires or Nanotubes
• Torsion Testing of Wire | Equipment
• Tensile Testing Aluminum and Magnesium Metal Alloys
• Tensile Test Equipment for Rebar
• Tensile Test Machines for Steel Products
• Tensile Grips - Capstan, Pneumatic, and Wedge for Wire
• How to Plan Tensile Tests for Wire Crimp, Solder, and Lugs
• How to Configure Test Equipment for Tensile Test of Metals
• Biaxial Tension Tests of Sheet Metal
• Biaxial fracture toughness and crack growth tests of metal
• Low Cycle Fatigue (LCF) of Metals at High Temperature
• Strain Controlled Low Cycle Fatigue Testing Equipment
• Guided Bend Test of Metal Welds
• Four Steps to Select Compression Test Equipment for Metals
• Fine Wire Test Grips and Equipment
• Tensile Testing of Nitinol Wire
• Wire Tensile Testing Standards: Crimp, Solder, and Lug Wire Connections
• Wire Torsion Strength Test | Equipment
• How to pull test cable and wire products
• Cable Proof Load Limit Mechanical Test Equipment
• Metal Forging Fatigue, Fracture and Tensile Test Equipment
• Steel Reinforcing Bar or Rebar Tensile Test Equipment
• Stainless Steel Fatigue Cryogenic Tests
• Weld Strength Tests using Guided Bend and Tensile Fixtures | Equipment
• Metals Fracture Toughness Testing | Machines & Equipment
• Testing Metals for Thermo Mechanical Fatigue (TMF) Life | Equipment
• Metals Fatigue Crack Propagation Tests with Variable Amplitude Loading
• Metal Chain Static and Fatigue Test Application
• Weld Ductility Bend Test
• Metal Ductility Bend Test
• High Cycle Fatigue (HCF) of Metals
• Metals Crack Growth Planar Biaxial Mode
• Metals Testing - Axial Torsion | Equipment
• Metals Fatigue Testing at High Temperatures
• Single-Lap-Joint Adhesively Bonded Metal Specimens Apparent Shear Strength by Tension Loading
• Steel Pipeline Tensile Testing
• Rebar Tensile and Bend Testing
• Pre-stressed Concrete Multi-Wire Strand Tensile Tests
• Structural Steel Tension Testing
• Gray Iron Casting Dumbbell Samples - Tensile Testing
• Iron Pipe Tensile Testing
• Elevated Temperature Tension Tests of Metals
• Sheet Metal R and N values Testing
• Metallic Materials Tensile Testing
• Tensile Testing of Thin Metal Foil
• Tensile Testing of Metal Dogbone Specimens
• Testing Materials in Radioactive Hot Cells
• Wires, Cables and Rope Pull Testing
  
   

Applicable Standards

• ASTM A1022 Stainless Steel Wire Concrete Reinforcement Test Equipment
• ASTM A1044 Steel Stud Assemblies Test Machine
• ASTM A370 Mechanical Testing of Steel Products
• ASTM A496 Tension Bend Steel Wire Test Equipment
• ASTM A938 Torsional Test of Wire
• ASTM D1002 Lap Shear Testing for Adhesively Bonded Metals
• ASTM E1820 Fracture Toughness Test Equipment for Metals
• ASTM E190 Guided Bend Test Equipment for Ductility of Welds
• ASTM E21 Elevated Temperature Tension Tests of Metals
• ASTM E2368 Thermomechanical Fatigue Test Equipment
• ASTM E2760 Creep Fatigue Crack Growth Test Equipment
• ASTM E290 Bend Testing of Material for Ductility
• ASTM E399 Linear-Elastic Plane-Strain Fracture Toughness (K1c) Testing of Metallic Materials
• ASTM E466 Load Controlled Constant Amplitude Fatigue Tests of Metals
• ASTM E606 Strain-Controlled High and Low Cycle Fatigue Testing
• ASTM E647 Fatigue Crack Growth Test Equipment
• ASTM E8 Tension Testing of Metallic Materials
• ASTM E9 Compression Testing of Metallic Materials at Room Temperature
• ASTM F2516 Tension Testing Equipment for Nickel-Titanium Superelastic Materials
• ASTM F382 Flexural Fatigue Bone Plate Fixation Devices Test Equipment
• ASTM F384 Bending Fatigue Orthopedic Fixation Devices Test Equipment
• ISO 15630 Steel Reinforcement of Concrete
• ISO 6892-1 & 2 Metal Tensile Testing
• ISO 7800 Metal Wire Torsion test
• ANSI/AWS B4.0 Mechanical Testing of Welds